| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: pca953x: fix pca953x_irq_bus_sync_unlock race
Ensure that `i2c_lock' is held when setting interrupt latch and mask in
pca953x_irq_bus_sync_unlock() in order to avoid races.
The other (non-probe) call site pca953x_gpio_set_multiple() ensures the
lock is held before calling pca953x_write_regs().
The problem occurred when a request raced against irq_bus_sync_unlock()
approximately once per thousand reboots on an i.MX8MP based system.
* Normal case
0-0022: write register AI|3a {03,02,00,00,01} Input latch P0
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
* Race case
0-0022: write register AI|08 {ff,00,00,00,00} Output P3
0-0022: write register AI|08 {03,02,00,00,01} *** Wrong register ***
0-0022: write register AI|12 {fc,00,00,00,00} Config P3
0-0022: write register AI|49 {fc,fd,ff,ff,fe} Interrupt mask P0 |
| In the Linux kernel, the following vulnerability has been resolved:
cachefiles: add missing lock protection when polling
Add missing lock protection in poll routine when iterating xarray,
otherwise:
Even with RCU read lock held, only the slot of the radix tree is
ensured to be pinned there, while the data structure (e.g. struct
cachefiles_req) stored in the slot has no such guarantee. The poll
routine will iterate the radix tree and dereference cachefiles_req
accordingly. Thus RCU read lock is not adequate in this case and
spinlock is needed here. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: don't unoptimize message in spi_async()
Calling spi_maybe_unoptimize_message() in spi_async() is wrong because
the message is likely to be in the queue and not transferred yet. This
can corrupt the message while it is being used by the controller driver.
spi_maybe_unoptimize_message() is already called in the correct place
in spi_finalize_current_message() to balance the call to
spi_maybe_optimize_message() in spi_async(). |
| In the Linux kernel, the following vulnerability has been resolved:
wireguard: allowedips: avoid unaligned 64-bit memory accesses
On the parisc platform, the kernel issues kernel warnings because
swap_endian() tries to load a 128-bit IPv6 address from an unaligned
memory location:
Kernel: unaligned access to 0x55f4688c in wg_allowedips_insert_v6+0x2c/0x80 [wireguard] (iir 0xf3010df)
Kernel: unaligned access to 0x55f46884 in wg_allowedips_insert_v6+0x38/0x80 [wireguard] (iir 0xf2010dc)
Avoid such unaligned memory accesses by instead using the
get_unaligned_be64() helper macro.
[Jason: replace src[8] in original patch with src+8] |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()
Userspace provided string 's' could trivially have the length zero. Left
unchecked this will firstly result in an OOB read in the form
`if (str[0 - 1] == '\n') followed closely by an OOB write in the form
`str[0 - 1] = '\0'`.
There is already a validating check to catch strings that are too long.
Let's supply an additional check for invalid strings that are too short. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/mm: Add NULL pointer check to crst_table_free() base_crst_free()
crst_table_free() used to work with NULL pointers before the conversion
to ptdescs. Since crst_table_free() can be called with a NULL pointer
(error handling in crst_table_upgrade() add an explicit check.
Also add the same check to base_crst_free() for consistency reasons.
In real life this should not happen, since order two GFP_KERNEL
allocations will not fail, unless FAIL_PAGE_ALLOC is enabled and used. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: fix crashes from deferred split racing folio migration
Even on 6.10-rc6, I've been seeing elusive "Bad page state"s (often on
flags when freeing, yet the flags shown are not bad: PG_locked had been
set and cleared??), and VM_BUG_ON_PAGE(page_ref_count(page) == 0)s from
deferred_split_scan()'s folio_put(), and a variety of other BUG and WARN
symptoms implying double free by deferred split and large folio migration.
6.7 commit 9bcef5973e31 ("mm: memcg: fix split queue list crash when large
folio migration") was right to fix the memcg-dependent locking broken in
85ce2c517ade ("memcontrol: only transfer the memcg data for migration"),
but missed a subtlety of deferred_split_scan(): it moves folios to its own
local list to work on them without split_queue_lock, during which time
folio->_deferred_list is not empty, but even the "right" lock does nothing
to secure the folio and the list it is on.
Fortunately, deferred_split_scan() is careful to use folio_try_get(): so
folio_migrate_mapping() can avoid the race by folio_undo_large_rmappable()
while the old folio's reference count is temporarily frozen to 0 - adding
such a freeze in the !mapping case too (originally, folio lock and
unmapping and no swap cache left an anon folio unreachable, so no freezing
was needed there: but the deferred split queue offers a way to reach it). |
| In the Linux kernel, the following vulnerability has been resolved:
filemap: replace pte_offset_map() with pte_offset_map_nolock()
The vmf->ptl in filemap_fault_recheck_pte_none() is still set from
handle_pte_fault(). But at the same time, we did a pte_unmap(vmf->pte).
After a pte_unmap(vmf->pte) unmap and rcu_read_unlock(), the page table
may be racily changed and vmf->ptl maybe fails to protect the actual page
table. Fix this by replacing pte_offset_map() with
pte_offset_map_nolock().
As David said, the PTL pointer might be stale so if we continue to use
it infilemap_fault_recheck_pte_none(), it might trigger UAF. Also, if
the PTL fails, the issue fixed by commit 58f327f2ce80 ("filemap: avoid
unnecessary major faults in filemap_fault()") might reappear. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: fix race between delayed_work() and ceph_monc_stop()
The way the delayed work is handled in ceph_monc_stop() is prone to
races with mon_fault() and possibly also finish_hunting(). Both of
these can requeue the delayed work which wouldn't be canceled by any of
the following code in case that happens after cancel_delayed_work_sync()
runs -- __close_session() doesn't mess with the delayed work in order
to avoid interfering with the hunting interval logic. This part was
missed in commit b5d91704f53e ("libceph: behave in mon_fault() if
cur_mon < 0") and use-after-free can still ensue on monc and objects
that hang off of it, with monc->auth and monc->monmap being
particularly susceptible to quickly being reused.
To fix this:
- clear monc->cur_mon and monc->hunting as part of closing the session
in ceph_monc_stop()
- bail from delayed_work() if monc->cur_mon is cleared, similar to how
it's done in mon_fault() and finish_hunting() (based on monc->hunting)
- call cancel_delayed_work_sync() after the session is closed |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: replace skb_put with skb_put_zero
Avoid potentially reusing uninitialized data |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: mv88e6xxx: Correct check for empty list
Since commit a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO
busses") mv88e6xxx_default_mdio_bus() has checked that the
return value of list_first_entry() is non-NULL.
This appears to be intended to guard against the list chip->mdios being
empty. However, it is not the correct check as the implementation of
list_first_entry is not designed to return NULL for empty lists.
Instead, use list_first_entry_or_null() which does return NULL if the
list is empty.
Flagged by Smatch.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: Account for stopped queues when reading NIC stats
We now account for the fact that the NIC might send us stats for a
subset of queues. Without this change, gve_get_ethtool_stats might make
an invalid access on the priv->stats_report->stats array. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: fix a possible leak when destroy a ctrl during qp establishment
In nvmet_sq_destroy we capture sq->ctrl early and if it is non-NULL we
know that a ctrl was allocated (in the admin connect request handler)
and we need to release pending AERs, clear ctrl->sqs and sq->ctrl
(for nvme-loop primarily), and drop the final reference on the ctrl.
However, a small window is possible where nvmet_sq_destroy starts (as
a result of the client giving up and disconnecting) concurrently with
the nvme admin connect cmd (which may be in an early stage). But *before*
kill_and_confirm of sq->ref (i.e. the admin connect managed to get an sq
live reference). In this case, sq->ctrl was allocated however after it was
captured in a local variable in nvmet_sq_destroy.
This prevented the final reference drop on the ctrl.
Solve this by re-capturing the sq->ctrl after all inflight request has
completed, where for sure sq->ctrl reference is final, and move forward
based on that.
This issue was observed in an environment with many hosts connecting
multiple ctrls simoutanuosly, creating a delay in allocating a ctrl
leading up to this race window. |
| In the Linux kernel, the following vulnerability has been resolved:
IB/core: Implement a limit on UMAD receive List
The existing behavior of ib_umad, which maintains received MAD
packets in an unbounded list, poses a risk of uncontrolled growth.
As user-space applications extract packets from this list, the rate
of extraction may not match the rate of incoming packets, leading
to potential list overflow.
To address this, we introduce a limit to the size of the list. After
considering typical scenarios, such as OpenSM processing, which can
handle approximately 100k packets per second, and the 1-second retry
timeout for most packets, we set the list size limit to 200k. Packets
received beyond this limit are dropped, assuming they are likely timed
out by the time they are handled by user-space.
Notably, packets queued on the receive list due to reasons like
timed-out sends are preserved even when the list is full. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Ignore too large handle values in BIG
hci_le_big_sync_established_evt is necessary to filter out cases where the
handle value is belonging to ida id range, otherwise ida will be erroneously
released in hci_conn_cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
bluetooth/hci: disallow setting handle bigger than HCI_CONN_HANDLE_MAX
Syzbot hit warning in hci_conn_del() caused by freeing handle that was
not allocated using ida allocator.
This is caused by handle bigger than HCI_CONN_HANDLE_MAX passed by
hci_le_big_sync_established_evt(), which makes code think it's unset
connection.
Add same check for handle upper bound as in hci_conn_set_handle() to
prevent warning. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix double free err_addr pointer warnings
In amdgpu_umc_bad_page_polling_timeout, the amdgpu_umc_handle_bad_pages
will be run many times so that double free err_addr in some special case.
So set the err_addr to NULL to avoid the warnings. |
| In the Linux kernel, the following vulnerability has been resolved:
jffs2: Fix potential illegal address access in jffs2_free_inode
During the stress testing of the jffs2 file system,the following
abnormal printouts were found:
[ 2430.649000] Unable to handle kernel paging request at virtual address 0069696969696948
[ 2430.649622] Mem abort info:
[ 2430.649829] ESR = 0x96000004
[ 2430.650115] EC = 0x25: DABT (current EL), IL = 32 bits
[ 2430.650564] SET = 0, FnV = 0
[ 2430.650795] EA = 0, S1PTW = 0
[ 2430.651032] FSC = 0x04: level 0 translation fault
[ 2430.651446] Data abort info:
[ 2430.651683] ISV = 0, ISS = 0x00000004
[ 2430.652001] CM = 0, WnR = 0
[ 2430.652558] [0069696969696948] address between user and kernel address ranges
[ 2430.653265] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 2430.654512] CPU: 2 PID: 20919 Comm: cat Not tainted 5.15.25-g512f31242bf6 #33
[ 2430.655008] Hardware name: linux,dummy-virt (DT)
[ 2430.655517] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 2430.656142] pc : kfree+0x78/0x348
[ 2430.656630] lr : jffs2_free_inode+0x24/0x48
[ 2430.657051] sp : ffff800009eebd10
[ 2430.657355] x29: ffff800009eebd10 x28: 0000000000000001 x27: 0000000000000000
[ 2430.658327] x26: ffff000038f09d80 x25: 0080000000000000 x24: ffff800009d38000
[ 2430.658919] x23: 5a5a5a5a5a5a5a5a x22: ffff000038f09d80 x21: ffff8000084f0d14
[ 2430.659434] x20: ffff0000bf9a6ac0 x19: 0169696969696940 x18: 0000000000000000
[ 2430.659969] x17: ffff8000b6506000 x16: ffff800009eec000 x15: 0000000000004000
[ 2430.660637] x14: 0000000000000000 x13: 00000001000820a1 x12: 00000000000d1b19
[ 2430.661345] x11: 0004000800000000 x10: 0000000000000001 x9 : ffff8000084f0d14
[ 2430.662025] x8 : ffff0000bf9a6b40 x7 : ffff0000bf9a6b48 x6 : 0000000003470302
[ 2430.662695] x5 : ffff00002e41dcc0 x4 : ffff0000bf9aa3b0 x3 : 0000000003470342
[ 2430.663486] x2 : 0000000000000000 x1 : ffff8000084f0d14 x0 : fffffc0000000000
[ 2430.664217] Call trace:
[ 2430.664528] kfree+0x78/0x348
[ 2430.664855] jffs2_free_inode+0x24/0x48
[ 2430.665233] i_callback+0x24/0x50
[ 2430.665528] rcu_do_batch+0x1ac/0x448
[ 2430.665892] rcu_core+0x28c/0x3c8
[ 2430.666151] rcu_core_si+0x18/0x28
[ 2430.666473] __do_softirq+0x138/0x3cc
[ 2430.666781] irq_exit+0xf0/0x110
[ 2430.667065] handle_domain_irq+0x6c/0x98
[ 2430.667447] gic_handle_irq+0xac/0xe8
[ 2430.667739] call_on_irq_stack+0x28/0x54
The parameter passed to kfree was 5a5a5a5a, which corresponds to the target field of
the jffs_inode_info structure. It was found that all variables in the jffs_inode_info
structure were 5a5a5a5a, except for the first member sem. It is suspected that these
variables are not initialized because they were set to 5a5a5a5a during memory testing,
which is meant to detect uninitialized memory.The sem variable is initialized in the
function jffs2_i_init_once, while other members are initialized in
the function jffs2_init_inode_info.
The function jffs2_init_inode_info is called after iget_locked,
but in the iget_locked function, the destroy_inode process is triggered,
which releases the inode and consequently, the target member of the inode
is not initialized.In concurrent high pressure scenarios, iget_locked
may enter the destroy_inode branch as described in the code.
Since the destroy_inode functionality of jffs2 only releases the target,
the fix method is to set target to NULL in jffs2_i_init_once. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: always do the basic checks for btrfs_qgroup_inherit structure
[BUG]
Syzbot reports the following regression detected by KASAN:
BUG: KASAN: slab-out-of-bounds in btrfs_qgroup_inherit+0x42e/0x2e20 fs/btrfs/qgroup.c:3277
Read of size 8 at addr ffff88814628ca50 by task syz-executor318/5171
CPU: 0 PID: 5171 Comm: syz-executor318 Not tainted 6.10.0-rc2-syzkaller-00010-g2ab795141095 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
print_address_description mm/kasan/report.c:377 [inline]
print_report+0x169/0x550 mm/kasan/report.c:488
kasan_report+0x143/0x180 mm/kasan/report.c:601
btrfs_qgroup_inherit+0x42e/0x2e20 fs/btrfs/qgroup.c:3277
create_pending_snapshot+0x1359/0x29b0 fs/btrfs/transaction.c:1854
create_pending_snapshots+0x195/0x1d0 fs/btrfs/transaction.c:1922
btrfs_commit_transaction+0xf20/0x3740 fs/btrfs/transaction.c:2382
create_snapshot+0x6a1/0x9e0 fs/btrfs/ioctl.c:875
btrfs_mksubvol+0x58f/0x710 fs/btrfs/ioctl.c:1029
btrfs_mksnapshot+0xb5/0xf0 fs/btrfs/ioctl.c:1075
__btrfs_ioctl_snap_create+0x387/0x4b0 fs/btrfs/ioctl.c:1340
btrfs_ioctl_snap_create_v2+0x1f2/0x3a0 fs/btrfs/ioctl.c:1422
btrfs_ioctl+0x99e/0xc60
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xfc/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcbf1992509
RSP: 002b:00007fcbf1928218 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcbf1a1f618 RCX: 00007fcbf1992509
RDX: 0000000020000280 RSI: 0000000050009417 RDI: 0000000000000003
RBP: 00007fcbf1a1f610 R08: 00007ffea1298e97 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fcbf19eb660
R13: 00000000200002b8 R14: 00007fcbf19e60c0 R15: 0030656c69662f2e
</TASK>
And it also pinned it down to commit b5357cb268c4 ("btrfs: qgroup: do not
check qgroup inherit if qgroup is disabled").
[CAUSE]
That offending commit skips the whole qgroup inherit check if qgroup is
not enabled.
But that also skips the very basic checks like
num_ref_copies/num_excl_copies and the structure size checks.
Meaning if a qgroup enable/disable race is happening at the background,
and we pass a btrfs_qgroup_inherit structure when the qgroup is
disabled, the check would be completely skipped.
Then at the time of transaction commitment, qgroup is re-enabled and
btrfs_qgroup_inherit() is going to use the incorrect structure and
causing the above KASAN error.
[FIX]
Make btrfs_qgroup_check_inherit() only skip the source qgroup checks.
So that even if invalid btrfs_qgroup_inherit structure is passed in, we
can still reject invalid ones no matter if qgroup is enabled or not.
Furthermore we do already have an extra safety inside
btrfs_qgroup_inherit(), which would just ignore invalid qgroup sources,
so even if we only skip the qgroup source check we're still safe. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ntb_netdev: Move ntb_netdev_rx_handler() to call netif_rx() from __netif_rx()
The following is emitted when using idxd (DSA) dmanegine as the data
mover for ntb_transport that ntb_netdev uses.
[74412.546922] BUG: using smp_processor_id() in preemptible [00000000] code: irq/52-idxd-por/14526
[74412.556784] caller is netif_rx_internal+0x42/0x130
[74412.562282] CPU: 6 PID: 14526 Comm: irq/52-idxd-por Not tainted 6.9.5 #5
[74412.569870] Hardware name: Intel Corporation ArcherCity/ArcherCity, BIOS EGSDCRB1.E9I.1752.P05.2402080856 02/08/2024
[74412.581699] Call Trace:
[74412.584514] <TASK>
[74412.586933] dump_stack_lvl+0x55/0x70
[74412.591129] check_preemption_disabled+0xc8/0xf0
[74412.596374] netif_rx_internal+0x42/0x130
[74412.600957] __netif_rx+0x20/0xd0
[74412.604743] ntb_netdev_rx_handler+0x66/0x150 [ntb_netdev]
[74412.610985] ntb_complete_rxc+0xed/0x140 [ntb_transport]
[74412.617010] ntb_rx_copy_callback+0x53/0x80 [ntb_transport]
[74412.623332] idxd_dma_complete_txd+0xe3/0x160 [idxd]
[74412.628963] idxd_wq_thread+0x1a6/0x2b0 [idxd]
[74412.634046] irq_thread_fn+0x21/0x60
[74412.638134] ? irq_thread+0xa8/0x290
[74412.642218] irq_thread+0x1a0/0x290
[74412.646212] ? __pfx_irq_thread_fn+0x10/0x10
[74412.651071] ? __pfx_irq_thread_dtor+0x10/0x10
[74412.656117] ? __pfx_irq_thread+0x10/0x10
[74412.660686] kthread+0x100/0x130
[74412.664384] ? __pfx_kthread+0x10/0x10
[74412.668639] ret_from_fork+0x31/0x50
[74412.672716] ? __pfx_kthread+0x10/0x10
[74412.676978] ret_from_fork_asm+0x1a/0x30
[74412.681457] </TASK>
The cause is due to the idxd driver interrupt completion handler uses
threaded interrupt and the threaded handler is not hard or soft interrupt
context. However __netif_rx() can only be called from interrupt context.
Change the call to netif_rx() in order to allow completion via normal
context for dmaengine drivers that utilize threaded irq handling.
While the following commit changed from netif_rx() to __netif_rx(),
baebdf48c360 ("net: dev: Makes sure netif_rx() can be invoked in any context."),
the change should've been a noop instead. However, the code precedes this
fix should've been using netif_rx_ni() or netif_rx_any_context(). |
